here you go Heather, If you have the 5.3 liter engine, the price for the new pump, $$96.89 Labor would be 3.8 hours to replace. Most shops charge from $ 60-80 per hour. Dealers More. If you have a 4.3 liter engine, Part is $65.00 labor would be 3.3 hours. So it should cost about $362.89 plus tax for the 5.3 engine %26amp; $296.00 plus tax for the 4.3 engine. the 5.3 is a V-8 and 4.3 is a V-6 . You and find your engine size , if you do not know if it is a 6 or 8 cyl. by looking at the small white sticker under the hood compartment. I hope this will give you a better idea. Good Luck! :)How much does it cost to change a water pump on a 2005 chevy trailblazer?
Just labor would be around $50.-$75.How much does it cost to change a water pump on a 2005 chevy trailblazer?
the pump ita self is around 50-60 bucks and probably 200-300 to install replace antifreeze etc
parts cost hmm...just the pump about 80ish. replace hoses also about 15 more. labor about 70. so 165 if you get it done by some1 at a shop???
Depends on where you go, usually the time is around 1 hr to 1.5 (figure labor rate of your shop) and your pump and gasket price. Also if you want a heavy duty unit. To be fair I would need an engine size. I think the 6 is a little cheaper then the 8. Also they will need to coolant change and bleed out your system which usually that's around $80 at least in my area. I do them for around 160 to 500 depending on what it's in. Your pump is going to be around 45$ if they want more, look at your local parts store or shop ( RockAuto.com )
go to yoour nearest auto zone plop down about thirty nine dollar,s go to your nearrest garage and they will install it for about fifty buck,s
Sunday, November 21, 2010
How long does it take to change the water pump on a dodge 3.8 do you have to move the ac?
Well according to Mitchell on demand the labor charge is an hour. Which is not much at all. A do it yourselfer could handle this job. I believe there are 5 or 6 bolts that hold it in. The water pump is all the way at the bottom of the engine.How long does it take to change the water pump on a dodge 3.8 do you have to move the ac?
thanks dog you were about right. remove passenger wheel, wheel well cover and voila. except don't break the factory 10mm bolts off in the timing cover. they are factory loctited. sucks.
http://www.dodgetalk.com/forums/showthre
thanks dog you were about right. remove passenger wheel, wheel well cover and voila. except don't break the factory 10mm bolts off in the timing cover. they are factory loctited. sucks.
Report Abuse
How long does it take to change the water pump on a dodge 3.8 do you have to move the ac?http://www.dodgetalk.com/forums/showthre
How do you change a water pump and on 2002 pontiac grand am gt?
someone told me my water pump may be going out and it sounds like their is a loose barron inside of it, so how much is it and and if i was to have someone else to fix it how much will it cost meHow do you change a water pump and on 2002 pontiac grand am gt?
This should be a V6 engine correct. if looking at front of engine,toward the belt , the water pump is located behind pulley appox. 5 inches on the side toward radiator. highest pulley on right side of engine. Replacement can be performed easily without many special tools.. First loosens each of the pulley bolts on pump. Then release tension on belt and route away from pulley. Remove remaining pulley bolts and pulley , Water pump has 5 bolts holding it to cover assembly, Mark-index the way pump installs and remove. Clean all gasket material. Install new pump and gasket, refill system and to open air blled on cooler pipe near water pump to allow air to escape.How do you change a water pump and on 2002 pontiac grand am gt?
type how to replace water pump 2002 grand am
add video mioght find one an dalso try autozone.com type in your info and look for a how to tyhey have many there an dother guy layed it out pretty well4stuff for sale give me some boys names
This should be a V6 engine correct. if looking at front of engine,toward the belt , the water pump is located behind pulley appox. 5 inches on the side toward radiator. highest pulley on right side of engine. Replacement can be performed easily without many special tools.. First loosens each of the pulley bolts on pump. Then release tension on belt and route away from pulley. Remove remaining pulley bolts and pulley , Water pump has 5 bolts holding it to cover assembly, Mark-index the way pump installs and remove. Clean all gasket material. Install new pump and gasket, refill system and to open air blled on cooler pipe near water pump to allow air to escape.How do you change a water pump and on 2002 pontiac grand am gt?
type how to replace water pump 2002 grand am
add video mioght find one an dalso try autozone.com type in your info and look for a how to tyhey have many there an dother guy layed it out pretty well
1993 Pontiac 2.3 changed water pump, now no start?
I changed the water pump on a 2.3 liter Pontiac engine, now it cranks but won't start. Timing gears were locked in place during work, so timing is probably OK. How can I check the alignment of the timing gears to verify correct timing?1993 Pontiac 2.3 changed water pump, now no start?
If the timing gears were locked in place and you did not remove them, then that is not your problem.
Retrace your steps and see if you knocked a wire off or maybe you forgot to reconnect the crank angle sensor during reassembly.1993 Pontiac 2.3 changed water pump, now no start?
Notes: biennial oil changes and water as coolant= bad ideas. :(
This engine also had valve lifters that were so full of grit they wouldn't compress at all.
I have a '92 w/2.3, and I've changed the water pump...trying
to remember what is close by.
Maybe you unplugged the injector wiring harness?
Also check the wiring going to the ignition module (under
the aluminum cover)...may have pulled out.
Sounds like it hydralocked on you. For what reason did you originally change the pump? Overheating? Possible Coolant loss? These engines have had many coolant related problems historically, and often can be attributed to cracked blocks and cylinder head failures. This may have been the original problem.
you don't mess with your timing belt? if you do so you have to put on time
I gaurantee you that the timing is off..trust me..when you released the tensioner it may have jumped a tooth or two..i have a 94 grand am i just did a water pump on..remember all the gears..crank and camshaft(s) dots have to be lined up perfectly..no room for error.
only a auto shop can tell you i am pontiac master tech and the only way to check for timeng alignment is to remove cover from passenger side of engine and check all marks.if the car was running when you carried to have water pump installed it is a problem with the timeing being out of alignment i have done many many of these and the job takes 8 hours to do i that is to but a water pump on this car .its is very easy to get out of alignment and even harder to correct. but if car was not running before installing water pump the problem could be ignition module,with is about 400 to 500 hundred.fuel pump 300.00 or crank sensor these are the only things that will stop car from running other than no gas. this is one of the hardest engines nown to work on so always carry to a pontiac dealer normal auto shops are a wast of time and money and generaly only make things worst. hope this helps.
If the timing gears were locked in place and you did not remove them, then that is not your problem.
Retrace your steps and see if you knocked a wire off or maybe you forgot to reconnect the crank angle sensor during reassembly.1993 Pontiac 2.3 changed water pump, now no start?
Notes: biennial oil changes and water as coolant= bad ideas. :(
This engine also had valve lifters that were so full of grit they wouldn't compress at all.
Report Abuse
I have a '92 w/2.3, and I've changed the water pump...trying
to remember what is close by.
Maybe you unplugged the injector wiring harness?
Also check the wiring going to the ignition module (under
the aluminum cover)...may have pulled out.
Sounds like it hydralocked on you. For what reason did you originally change the pump? Overheating? Possible Coolant loss? These engines have had many coolant related problems historically, and often can be attributed to cracked blocks and cylinder head failures. This may have been the original problem.
you don't mess with your timing belt? if you do so you have to put on time
I gaurantee you that the timing is off..trust me..when you released the tensioner it may have jumped a tooth or two..i have a 94 grand am i just did a water pump on..remember all the gears..crank and camshaft(s) dots have to be lined up perfectly..no room for error.
only a auto shop can tell you i am pontiac master tech and the only way to check for timeng alignment is to remove cover from passenger side of engine and check all marks.if the car was running when you carried to have water pump installed it is a problem with the timeing being out of alignment i have done many many of these and the job takes 8 hours to do i that is to but a water pump on this car .its is very easy to get out of alignment and even harder to correct. but if car was not running before installing water pump the problem could be ignition module,with is about 400 to 500 hundred.fuel pump 300.00 or crank sensor these are the only things that will stop car from running other than no gas. this is one of the hardest engines nown to work on so always carry to a pontiac dealer normal auto shops are a wast of time and money and generaly only make things worst. hope this helps.
How hard is it to change the water pump on a 2000 pontiac gran prix?
On the 3.1 - piece of cake. One caveat - have you ever done this before? If not - buy a repair manual from a parts store that has step by step instructions. The main thing to keep in mind is to clean off the old gasket as thoroughly as possible. Leaving even a little of the old gasket on the manifold will make for a bad seal and your new pump will leak. It's not necessary to use anything other than the gasket that comes with the new pump IF you clean it completely prior to installing. Us a 'light' putty knife to evenly take it all down to the metal - be careful, however, as the block is aluminum - too aggressive with the removal and you could damage the area.
Good luck
Good luck
I need to l know how to change the water pump, water pump belt, and pulleys on a 2000 cadillac eldorado. ?
My boyfriend will be doing the work for me. I told him I would try to find him some directions. We had the car in the shop to get a new radiator when we found out the water pump belt had spilt and parts of it were melted to the pulleys. Now we have to change the pulleys and the belt. My boyfriend decided to change the pump as well since that could have caused the problem with the belt and pulleys. Thanks a bunch!I need to l know how to change the water pump, water pump belt, and pulleys on a 2000 cadillac eldorado. ?
I have a real good friend who had worked on the 4.0L version of this Northstar in an Olds Aurora. It was a water pump and related junk, too.
He hated that.
Your b/f will be an EX-b/f once he even tries to tackle this job.
Send the car to a good shop and save your relationship.
This is not a joke. Your b/f does not deserve a task this horrendous. I hope.I need to l know how to change the water pump, water pump belt, and pulleys on a 2000 cadillac eldorado. ?
This task is way too complicated to address here. It is a reasonably difficult job. Go to a parts store and purchase a repair manual specific to that car and you should be okay. By the way, great idea to replace the pump; those belts do not fail for no reason. And do not-repeat, do not!- use a rebuilt water pump! Get a new one, or you'll be sorry.
no a trusty mechanic needs to do it or he will have some serious issues to do with.
I have a real good friend who had worked on the 4.0L version of this Northstar in an Olds Aurora. It was a water pump and related junk, too.
He hated that.
Your b/f will be an EX-b/f once he even tries to tackle this job.
Send the car to a good shop and save your relationship.
This is not a joke. Your b/f does not deserve a task this horrendous. I hope.I need to l know how to change the water pump, water pump belt, and pulleys on a 2000 cadillac eldorado. ?
This task is way too complicated to address here. It is a reasonably difficult job. Go to a parts store and purchase a repair manual specific to that car and you should be okay. By the way, great idea to replace the pump; those belts do not fail for no reason. And do not-repeat, do not!- use a rebuilt water pump! Get a new one, or you'll be sorry.
no a trusty mechanic needs to do it or he will have some serious issues to do with.
Does anyone know how to change a water pump on a 1989 Chevy Silverado 350. 2 wheel Drive?
http://www.extremehowto.com/xh/article.a
http://www.aa1car.com/library/water_pumpDoes anyone know how to change a water pump on a 1989 Chevy Silverado 350. 2 wheel Drive?
Best way to know all about your car is to buy a Chiltons Manual. Online or at most auto parts store. They are amazing books.
Good Luck. Oh and the 25 dollar price is a bargain, cheaper than screwing it up and paying someone else to fix it :)Does anyone know how to change a water pump on a 1989 Chevy Silverado 350. 2 wheel Drive?
you are going to skin your knuckles.
Id spend the 14 dollars and get a chiltons manual at your local parts store. Will have detailed steps.
http://www.aa1car.com/library/water_pumpDoes anyone know how to change a water pump on a 1989 Chevy Silverado 350. 2 wheel Drive?
Best way to know all about your car is to buy a Chiltons Manual. Online or at most auto parts store. They are amazing books.
Good Luck. Oh and the 25 dollar price is a bargain, cheaper than screwing it up and paying someone else to fix it :)Does anyone know how to change a water pump on a 1989 Chevy Silverado 350. 2 wheel Drive?
you are going to skin your knuckles.
Id spend the 14 dollars and get a chiltons manual at your local parts store. Will have detailed steps.
Subscribe to:
Posts (Atom)